How to Choose the Right LED High Bay Light for Your Warehouse

Most high bay mistakes are made before the first quotation: the fixture is chosen by wattage instead of mounting height, beam angle and the work below. This guide walks through the six decisions that actually affect the result.

1. Start with mounting height, not floor area

Two warehouses with the same floor area can need very different fixtures. A 6 m ceiling and a 12 m ceiling change the optics, wattage and spacing. Measure the distance from the floor to the fixture, not to the roof deck; sprinklers, ductwork and racking all reduce the usable mounting height.

As a starting point, 6–8 m ceilings usually suit 100–150W high bays with 90° or 120° optics. Heights of 8–12 m generally call for 150–200W and a 60° or 90° optic. Above 12 m, 200–240W with a narrow optic is common, but the racking layout still decides the final choice.

2. Match the beam angle to the racking

In a high-rack warehouse, the useful surface is the pallet face, not only the floor. A wide 120° beam spreads light across the aisle but wastes it on the racking structure and the air. A 60° beam puts more light on the pallet faces, provided the fixtures are positioned over the aisle and the spacing is correct.

For open floor areas and low-bay storage, 90° or 120° optics give a more even distribution. If you have a racking drawing, mark the aisle centre lines and the beam direction before choosing a lens.

3. Compare lumens and efficacy, not just watts

A 150W fixture at 100 lm/W delivers 15,000 lumens; a 150W fixture at 140 lm/W delivers 21,000 lumens. The wattage tells you the energy bill, not the light on the floor. Ask for the lumen output and efficacy at the CCT you are buying, and confirm whether the figure is typical or maximum.

Also check the lumen maintenance specification. A fixture with a lower initial output but a stable driver and good thermal design can deliver more useful light after two years than a cheap fixture running at its thermal limit.

4. Check IP, IK and the actual environment

Warehouses are not all the same. A dry distribution centre may only need IP20/IP40, while a washdown area, a cold store or a dusty workshop needs a sealed optical chamber. IP65 is a common choice for industrial high bays because it handles dust and water jets without adding much cost.

Impact rating (IK) matters where forklifts or overhead cranes operate. A tempered-glass lens and a protected driver compartment reduce the chance of a broken fixture after a knock.

5. Decide on controls before you buy

Dimming and occupancy sensing are easier to specify at the order stage than to retrofit. Aisles with intermittent traffic can use microwave sensors; areas with daylight contribution can use photocells or scheduled dimming. If the project may add controls later, choose a driver with 0–10V or DALI input now.

Emergency lighting is a separate requirement. If escape routes need maintained or non-maintained emergency operation, confirm the battery type, duration and testing method with the supplier.

6. Look at the driver, surge protection and warranty

The LED board often outlives the driver. Ask which driver brand is used, whether it is replaceable from below, and what surge protection is included. A 10kV surge module is inexpensive at the factory and expensive to add after a failure.

Warranty terms should state what is covered, for how long, and whether spare drivers are available. A 3-year warranty with local spare parts can be more useful than a 5-year warranty with no service path.

Quick selection starting points

Mounting heightTypical wattageBeam angleBest use
4–6 m80–100W90°–120°Low-bay storage, workshops
6–8 m100–150W90°General warehouse floor
8–10 m150–200W60°–90°Racking aisles
10–12 m200–240W60°High-rack, narrow aisles

Starting points only. Confirm with a lighting layout using the actual racking and reflectance values.

Need a second opinion?

Send the building dimensions, mounting height and racking layout. We will recommend a wattage, beam angle and spacing for the application. See our LED high bay range or request a layout review.

Planning a warehouse retrofit?

Share the aisle width, racking height and mounting height. We will come back with a fixture and spacing proposal.

Lumindus Lighting is a fictional brand. This website is a demo built for SEO and indexing practice.

Scroll to Top